VIDEO: Old work rework electrical box hole cutting and sizing.
Hole saws are not always a one size fits all old-work boxes. Before you go drilling 6in holes make sure you do not need a 6 3 8in. Make the holes perfect so you do not use a tube of caulk to seal the gaps.
After the 2016 floods we required a temporary power pole. The city inspector failed the pole for not having GFCI on both the 30 amp and 50 amp circuits. We were using the 30 amp and 50 amp for RVs and Campers that were already protected.
By Murray Wennerlund published 7-18-2023 updated 7-18-2023
Make a contribution
| Print
| GFCI RV
| 105 views
I am asked often if I would do carpentry work in my area. I'm getting too slow to actually handle most of the jobs I'm asked to do. I'd like to handoff the work to a carpenter that's better than me. I'm always looking for a good carpenter helper for projects I take on. Contact me and get listed and working.
With more people building homes more energy efficient we have to expand our reading to be able to correctly design homes that provide the best overall energy saving experience. Heating, Cooling and Moisture control will be our main focus in this article.
If you need a quote for a new manufactured home for the Louisiana Restore program send a note with your old VIN number and your status in the program. All we can do is help you get the quotes for the MHU you are looking to replace. Contact me
When I design a wall I always look at how the wall transfers the weight from above then I look at the openings and how I can make them easier to work with when choosing windows and doors. If you know the width, you know header so place it under top plate
When your worker is new and you are just not ready to let them go until you try a little training. I used to get the boot up the rear threat which meant to look, focus, learn how to do it like the carpenter would do it.
By Murray Wennerlund published 1-16-2023 updated 3-17-2023
Make a contribution
| Print
| Training
| 145 views
When you are navigating the federal disaster assistance agencies your first stop should be to the TruckAndTools.Com Disaster Resources. Every disaster agency uses the same process but not every disaster agency follows strict policy and guidance. Don't go into your disaster recovery with blind trust of your federal and state agencies that are leading the push to get you sheltered and out of the program.
Hole saws are not always a one size fits all old-work boxes. Before you go drilling 6in holes make sure you do not need a 6 3/8in. Make the holes perfect so you do not use a tube of caulk to seal the gaps.
When you are working with unvented or have a sealed roof design their are a few set rules in the IRC 2015 that need to be reviewed. After your code is covered we monitor our actual heat and humidity levels to prevent roof shingle and deck damage.
Read full articles from TruckAndTools.Com and explore endless topics, magazines and more on your phone or tablet with Google News. TruckAndTools.Com - Google News.
Or add our TruckAndTools.Com RSS feed to your favorite news reader and keep up when new information is shared.
Many times your fastener schedule isnt complete or may actually be missing from your design prints. Its up to the homeowner to make sure every fastener used in your build is what the industry calls for and meets or exceeds code requirements.
By Murray Wennerlund published 9-26-2022 updated 9-26-2022
Make a contribution
| Print
| Fastener
| 137 views
For some households, the information I provide helps them get back in their homes. Others I've had a hand in helping them recovery from some of their disaster debt burden. In any case, when you use the information I provide and it's helpful and makes you more successful with your disaster rebuild or new construction then feel free to contribute what you can and when you can. It helps with the hours of unpaid research and reading.
You must become a member of TruckAndTools.Com, make a post sharing what needs to be repaired then add to your post as you complete your repairs the how, who, what, when and where of it all.
By Murray Wennerlund published 9-10-2022 updated 9-10-2022
Make a contribution
| Print
| Projects
| 178 views